How to sew a battery with drywall and create a durable and beautiful box?

How to sew a battery with drywall? And most importantly, how to make it so that the box is aesthetically attractive and pleasant? We will try to answer these questions and present a detailed methodology.

Gypsum cardboard pipe – aesthetics of modern material

The video tells – how to hide communications under drywall

If you want the shocking pipes or batteries not to be visible in the room, then you can hide them using a box. What should it be? Convenient to use. You should always have access to batteries and pipes. And in the event of their flow, it is desirable that the box is easily dismantled. In addition, it should be environmentally friendly.

The box should have a pleasant appearance. That is why it is finished on top of plaster or paint for the overall design of the room. One question remains – what material to use in its manufacture? Drywall was and remains universal (preferably waterproof). The material has excellent characteristics (not grief, easily mounted, has elasticity and good noise absorption). Although some consumers use, sometimes, plastic. Its advantage over GKL is that the material does not need to be additionally finished (paint). And its moisture resistance is an order of magnitude higher.

How to close the battery with drywall without unnecessary nerves?

So, if you still chose sheets for the work of GKL, then there is one main advantage in this. They are easily mounted and capable of bending properly. Therefore, problems with the manufacture of a box of the desired shape should not have arisen. So, how to sheathe a battery with a drywall? To do this, you will need the following materials:

GKL;

Putty;

Metal profiles.

First, the batteries are measured in order to produce the most accurate frame. Then they begin to mount the first guide profile. Use dowels or screws for this. Smoothness is checked using the construction level.

At the next stage, there are jumpers from the main profile. Mount them in a horizontal position to the guide. The distance between the jumpers should be 6 cm. Next, they make measurements in height and according to these data, the guide profile is attached to the floor from below and to the jumpers from above. In fact, the frame is ready. It remains only to cut drywall and attach it to the profiles using screws. Moreover, the screws need to be “immersed” into the material so that the hat does not stick out. At the last stage, it is necessary to mask the joints with putty. After drying it, you can apply for example paint. The question of how to close the heating battery with drywall should be completely exhausted.

Close the pipes with drywall in ten minutes

In addition to batteries, pipes can also be striking. For finishing work, the following materials will be needed: moisture -resistant GCL, hacksaw, putty, putty, screwdriver or screwdriver, screws, unit, bars or rack profiles, roulette or level. And pay attention, drywall should be strictly moisture resistant. This is justified by the fact that the pipes are often in wet rooms and, plus to everything, there is a risk of their course. So, how to sew pipes with drywall? At the initial stage, using a roulette, measure the distance from the ceiling to the floor. Then the profiles are cut off (3 or 4 pieces are required depending on the location of the pipe). You need to place them around the pipe that there is an angle of 90 degrees between them. In the event that the pipe is located in the center, 4 profiles are used.

Then the distance between these profiles is measured and the CD-60 profiles are inserted along their edges. Self -tapping screws are used for fastening. The frame is ready. It remains only to cut the drywall of the required size and attach it to the profiles. Self -tapping screws are also used for installation. At the next stage, the joints are treated with a sickle, and then the entire surface is finished with putty. If you want to make an even angle somewhere, then you need to take a metal corner and attach it with putty. Then align the space with the same mixture. Then the surface is fucked with sandpaper. First, coarse -grained, then fine -grained paper is used. At the finish stage, the box is faced with any suitable paint in shade. It is desirable that it be water-dispersing. Apply it with a roller or brush. The work is finished on this, and the question of how to sheathe with drywall the pipe should not arise anymore.

On a note! It is not necessary to use only paint for decoration of the box. You can also linen it with tiles or pasteen with wallpaper. It all depends on the alleged design and your wishes.